LEGO Duplo Play base
- Wooden play base
- Box of Duplo bricks
- 1/2 height instructions banner
- (Required from venue) tables and chairs
LEGO System Play base
- Wooden play base
- Box of Duplo bricks
- 1/2 height instructions banner
- (Required from venue) tables and chairs
Dino Dig
- Wooden Sandpit with mounted LEGO ‘bones’
- 1/2 height instructions banner
- (Required from venue) sand to fill and digging implements
Dino Footprint
- LEGO built dino footprint
LEGO Soft bricks
- Box of LEGO Soft bricks
Stamping Pillar
- Stamping Pillar
Graffiti Wall
- Wooden Graffiti wall in shape of dinosaur
- Wooden tray for bricks
- box of LEGO System 2x2 bricks in multiple colours.
Photo Opportunity
- Wooden photo opportunity front (with vinyled picture)
- Base, with removable rear panel for base
- 2 x angled supports.

Follow the same procedure for each play base;

Attach feet to the play base before unpacking. These will be stored in the tools flightcase. Screw the 4 feet into position.
Unpack the wooden play bases. WIth AT LEAST TWO PEOPLE, undo the ratchet strap holding the base to the pallet.
Lower the base down onto it’s feet - making sure not to put pressure on the feet as you roll it down. It is usually easiest to leave one side of the base on the pallet and lower the other down. Then, lift the base and remove the pallet.
FInd and unpack signaage for each play base. Instructions to assemble these can be found here. Note that these are generic, so adjust for the size of display that you have.
If necessary, touch up the grey paintwork surround
If necessary, touch up the top surface
Find the box of Duplo play bricks and place with play base.
Liase with venue as to how these bricks will be stored / presented.

Unpack Dino Dig and move into position
Fill with Sand
FInd and unpack signage for each play base. Instructions to assemble these can be found here. Note that these are generic, so adjust for the size of display that you have.
Liase with venue as to how tools will be stored / presented.

Give to venue. There is nothing else supplied for these.

Unpack all items and move to position
Check if items need repainting. If they do, spare paint for touch ups and painbrushes are in toolbox
Repaint if necessary
Once dry, hang the tray first. It should have 3 Ryman brackets on the rear, which will hang over screw heads. Alternatively, use mirror plates (not supplied)
Once tray is hung, hang graffiti wall itself above the tray. Ideally, the bottom edge of the wall should sit at the same level as the top of the tray (but not resting on the tray).

Unpack items.
1. You will have base unit (large, plywood box structure with a removable panel at the back.
2. Front panel (large plywood board, cut to shape and with vinyl graphic on top
3. 2 side supports (plywood, with holes for screws / captive nuts and angled ends)
4. Nuts and bolts (should be stored in flightcase).
Check front panel for damage. If this has been previously noted, a replacement vinyl should have been provided to apply. Please remove the previous one first, then apply the new one. Trim to size, making note of the 4 screw holes (2 to each size).
Put the base unit on its’ side - short edge downward
From underneath the base, check if the screws have been left in position. There are 2 long screws at the front and 2 to each side. All below the relevant slots.
Insert the front panel into the large slot, the image facing away from the base.
Insert the long bolts underneath the base unit, through the front panel and back into the base. Do not tighten yet, do up finger tight only
Insert the 2 side supports into the slots in the base unit
Insert nuts into part of side support nearest graphic
Insert hex head bolts through front of front panel into captive nuts in side supports
Screw bottom of side support into base unit
Roll the entire unit upright.
If necessary, insert 2 x concrete pads or sandbags into base unit for extra stability (not supplied)

Base Unit

Front Panel

Side Supports

Finished Photo Opportunity

Brick Dinos - Interactive (Play) features

Brick Dinos - Egg Nest